Propellerhead Reason - 3.0 - Control Surface Details Betriebsanweisung PDF herunterladen (Seite 20)

Novation

ReMOTE series

Requirements/Setting up:

• This model can be used with the ReMOTE 25 and other keyboards in the Novation

ReMOTE series.

• Please use the latest operating system for the ReMOTE keyboard - see www.no-

vationmusic.com for details.

• To use the ReMOTE with Reason, you need to connect it via USB or two-way

MIDI.

• Make sure the ReMOTE isn't write protected: press "Global", make sure the mem-

ory protect page is shown in the display and use the "Data/Value" knob to select

"off".

• When you add the ReMOTE in Reason, you must select the correct MIDI output

on the MIDI Output Port menu in the Add Control Surface dialog. Reason will then

upload a template to the edit buffer in the ReMOTE.

✪ If you like, you can then save these settings to any template memory lo-

cation on the ReMOTE by pressing “Write”. If you do this, you can also

set which template the ReMOTE should show each time you turn it on:

select the saved template, press "Global" and press "Write".

About the controls:

The controls are named as follows:

• The sliders/faders to the right are called Slider 1-8. The buttons below these are

called Button 1-8.

• The top row of knobs are called Knob 1-8. The buttons below these are called

Button 9-16.

• The bottom left row of rotary encoders are called Rotary 1-8. The buttons below

these are called Button 17-24.

About the default mapping:

D The transport buttons control the corresponding transport functions in

Reason.

D Reason supports the channel pressure (aftertouch) of the ReMOTE key-

board, but the result depends on the settings for the controlled device.

D The X/Y touch pad isn't mapped to any parameters by default, but you

can map it freely using Remote Overrides.

Note that there are two control surface items for each axis - you can map the touch

pad to four different Reason parameters (two for the X-axis and two for the Y-axis).

D Buttons 23-24 are used for Target Previous/Next Track (move master

keyboard input up or down in the track list).

D For devices with patches, buttons 15-16 select the previous/next patch.

D For effect devices, button 22 controls the Bypass/On/Off state.

D For most devices, the Data/Value rotary (below the display) is mapped to

master level.

However, on the two mixers the master level is controlled by Slider 8.

D Mixer 14:2

There are two keyboard shortcut variations, determining which mixer channels are

controlled (ch 1-7 or ch 8-14). The rotaries control pan and the knobs control Aux

send 1.

D Malström

There are two keyboard shortcut variations. In the first variation, the knobs and ro-

taries are mapped to parameters for Oscillator 1 and 2 respectively, while the slid-

ers control the filter parameters. In the second variation, the knobs and rotaries

control the modulators and additional oscillator settings, while the sliders control

additional filter and shaper parameters.

D Redrum

There are two keyboard shortcut variations, determining which drum channels are

controlled (drum 1-8 or drum 9-10). Button 9-12 and 17-20 select pattern; button

13-14 and 21-22 select bank.

D Matrix

Button 9-12 and 17-20 select pattern; button 13-14 and 21-22 select bank.

D BV-512 Vocoder

The sliders control the band levels. Use keyboard shortcut variations to select

which vocoder bands to control.

X-Station

Requirements/Setting up:

• If you have a ReMOTE 25 Audio, you can upgrade this to an X-Station - see

www.novationmusic.com.

• To use the X-Station with Reason, you need to connect it via USB or two-way

MIDI.

• Make sure the X-Station isn't write protected: press "Global", make sure the mem-

ory protect page is shown in the display and use the "Data/Value" knob to select

"off".

• When you add the X-Station in Reason, you must select the correct MIDI output

on the MIDI Output Port menu in the Add Control Surface dialog. Reason will then

upload a template to the edit buffer in the X-Station.

• If you like, you can then save these settings to any template memory location on

the X-Station. If you do this, you can also set which template the X-Station should

show each time you turn it on: select the saved template, press "Global" and

press "Write".

1 2 ... 15 16 17 18 19 20 21 22 23 24 25 26

Kommentare zu diesen Handbüchern

Keine Kommentare

Propellerhead Reason - 3.0 - Control Surface Details Betriebsanweisung Seite 20

Kommentare zu diesen Handbüchern