Propellerhead Reason - 1.0.1 Betriebshandbuch PDF herunterladen (Seite 158)

REBIRTH INPUT MACHINE

156

Introduction

The ReBirth Input Machine is a device dedicated to receiving audio from the

Propellerhead program “ReBirth RB-338” (version 2.01 and later). This is

achieved by using ReWire technology (see page 46), where Reason will act

as master and ReBirth as a slave device. If you don’t have ReBirth installed,

you cannot use this device. If you are a ReBirth user, you can use the Re-

Birth Input Machine for the following:

➜ Receive up to eighteen channels of streaming ReBirth channels in

Reason.

You can create more ReBirth Input Machines, but only one can be active

at a time.

➜ Sample accurate synchronization between the audio in the two pro-

grams.

➜ The two programs can share the same audio card and take advan-

tage of multiple outputs on that card.

Preparations

For the ReBirth Input Machine to correctly operate together with ReBirth, the

launch and quit order is very important. Proceed as follows:

Launching

1. Launch Reason.

2. Create a ReBirth Input Machine.

You may want create a Mixer prior to this step, otherwise the L/R Mix

channels will be routed directly to the Audio Hardware Interface. If you

have a Mixer, the L/R Mix output from the ReBirth Input Machine will be

automatically connected to the mixer’s first available audio inputs.

3. Launch ReBirth.

4. When ReBirth is launched, select Reason as the application in fo-

cus.

If both the “Reason is Rewire Master” and the “Active” indicator on the

ReBirth Input Machine are lit, this indicates that the launch procedure

was correct and that Reason and ReBirth are now locked and in sync.

➜ If only the “Active” indicator is lit, either the launch order was

wrong, or ReBirth is not installed properly.

5. Activate playback on Reason’s transport panel.

ReBirth and Reason are locked in perfect sync, and will follow any trans-

port commands in either of the programs.

! Note that there is no master/slave relationship for the transport con-

trols when using ReWire, as either device will control the other de-

vice’s transport. The audio, however, is streamed from ReBirth to

Reason, so in this aspect Reason is the master device.

Quitting

1. First quit ReBirth.

2. Then quit Reason.

Routing

When the two programs are synced, you can route any of the eighteen avail-

able outputs in ReBirth, to separate channels in a Reason Mixer, or to the

Hardware Interface for direct connection to a physical output on your audio

card.

If you flip the rack around, a row of 18 audio outputs is shown, with the L/R

Mix outputs auto-routed to your mixer or to the hardware interface.

What Signals are on the Outputs?

Mix-L and Mix-R

This is the regular master output in ReBirth RB-338. These are the only ste-

reo channels, all other channels are in mono.

➜ If none of the other channels are used, then this carries all the

sound from ReBirth.

➜ Signals that are activated separately are removed from this mix.

If for example the 909-Mix channel is activated, then Mix-L and Mix-R

carries all the sound from ReBirth RB-338 except the 909, which will ap-

pear on its own channel.

The individual outputs are described more closely in the ReWire chapter of

the ReBirth manual.

1 2 ... 153 154 155 156 157 158 159 160 161 162 163 ... 206 207

Propellerhead Reason - 1.0.1 Betriebshandbuch Seite 158

Kommentare zu diesen Handbüchern

Propellerhead Reason - 1.0.1 Betriebshandbuch Seite 158

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Software Propellerhead Reason - 1.0.1